WANT TO PAY LESS? – Ask about additional savings than those listed below!

Complete Service Upgrade: Installation of a new sub panel with up to 16 poles of breakers and proper grounding to main plumbing line and or ground rods. Up to a 10 feet run is included with a new surface mount meter base with riser or mast. Price does not include permit or inspection, does not include any repairs to the interior or exterior walls Price includes balancing load and torquing to manufacturers specifications.
Overhead Mount E100 480.165 100 amp 220 volt single phase 1-14028-100 amp panel w/main breaker, 1-R5412 1-‘x1 ½ “ Galv. Conduit, 1-11611 1 ½ “ Ent Hub, 2-1½ “2 Hole Conduit Strp, 1-11629-1½ “ Weatherhd, 1-11638-Roof flashing, 1-‘10096 #4 Thhn wire, 1-14032-8’x5/8” grnd rod ½” 3-12853- Alum to copper splicers or spil bolts, 1-14036-Ground rod clamp, 20’#6/1 armored ground wire, 4-11515 Bronze ground clamp, 16oz-21323 roof mastic, 1-½” Grnd Bshng, 1-12127-2P30A Brkr, 1-12130-2P40A Brkr, 1-12133-2P50A Brkr, 10-12133-1P15a or 20a Brkr, 10’ 12109 #8 Bore Grnd 4-14060A-3/8” Washers (flat), 4-R3312A-5/16” x 2 lag bolts E100 540.222 200 amp 220 volt single phase 1-200 amp panel w/main breaker, 1-R5413 10-‘x 2 “ Galv. Conduit, 1-11614 2 “ Ent Hub, 2-2 “2 Hole Conduit Strp, 1-11630-2 “ Weatherhd, 1-11641-Roof flashing, 1-‘10045-33’ 20Thhnwire, 1-14032-8’x3/4” grndrod ½” 3-12853- Alum to copper splicers or spil bolts, 1-14036-Ground rod clamp, 20’#4/1 armored ground wire, 4-11515 Bronze ground clamp, 16oz-21323 roof mastic, 1-½” Grnd Bshng, 1-12127-2P30A Brkr, 1-12130-2P40A Brkr, 1-12133-2P50A Brkr, 10-12133-1P15a or 20a Brkr, 10’ 12109 #8 Bore Grnd 4-14060A-3/8” Washers (flat), 4-R3312A-5/16” x 2 lag bolts Equipment brands: Challenger, GE or other equal value. NOTE: All service upgrade prices are priced for panel to stay in the same location. Relocation of panel will increase price at a rate of $74.00 per foot. PERMIT REQUIRED BY THE CITY. Check for overloaded circuits. Any additional breakers beyond 16 poles refer to page 12 for additional costs. Does Customer need extra branch circuits?			$6,958.90 $7,059.00
Value Rate is for money saving service agreement customers only.
Service Agreement Customer Benefits
m Member Priority Service		m On-Going Customer Discounts
m Bottom line Cost Benefit		m Preventative Maintenance
Fewer system repairs and safety inspections

WANT TO PAY LESS? – Ask about additional savings than those listed below!

Complete Service Upgrade: Installation of a new sub panel with up to 16 poles of breakers and proper grounding to main plumbing line and or ground rods. Up to a 10 feet run is included with a new surface mount meter base with riser or mast. Price does not include permit or inspection, does not include any repairs to the interior or exterior walls Price includes balancing load and torquing to manufacturers specifications.
Underground Mount E115 480.115 100 amp 220 volt single phase 1-14028-100 amp panel w/main breaker, 1-R5412 1-‘x1 ½ “ Galv. Conduit, 1-11611 1 ½ “ Ent Hub, 2-1½ “2 Hole Conduit Strp, 1-11629-1½ “ Weatherhd, 1-11638-Roof flashing, 1-‘10096 #4 Thhn wire, 1-14032-8’x5/8” grnd rod ½” 3-12853- Alum to copper splicers or spil bolts, 1-14036-Ground rod clamp, 20’#6/1 armored ground wire, 4-11515 Bronze ground clamp, 16oz-21323 roof mastic, 1-½” Grnd Bshng, 1-12127-2P30A Brkr, 1-12130-2P40A Brkr, 1-12133-2P50A Brkr, 10-12133-1P15a or 20a Brkr, 10’ 12109 #8 Bore Grnd 4-14060A-3/8” Washers (flat), 4-R3312A-5/16” x 2 lag bolts E125 540.165 200 amp 220 volt single phase 1-200 amp panel w/main breaker, 1-R5413 10-‘x 2 “ Galv. Conduit, 1-11614 2 “ Ent Hub, 2-2 “2 Hole Conduit Strp, 1-11630-2 “ Weatherhd, 1-11641-Roof flashing, 1-‘10045-33’ 20Thhnwire, 1-14032-8’x3/4” grndrod ½” 3-12853- Alum to copper splicers or spil bolts, 1-14036-Ground rod clamp, 20’#4/1 armored ground wire, 4-11515 Bronze ground clamp, 16oz-21323 roof mastic, 1-½” Grnd Bshng, 1-12127-2P30A Brkr, 1-12130-2P40A Brkr, 1-12133-2P50A Brkr, 10-12133-1P15a or 20a Brkr, 10’ 12109 #8 Bore Grnd 4-14060A-3/8” Washers (flat), 4-R3312A-5/16” x 2 lag bolts Equipment brands: Challenger, GE or other equal value. NOTE: All service upgrade prices are priced for panel to stay in the same location. Relocation of panel will increase price at a rate of $74.00 per foot. PERMIT REQUIRED BY THE CITY. Check for overloaded circuits. Any additional breakers beyond 16 poles refer to page 12 for additional costs. Does Customer need extra branch circuits?			$4,442.10 $5,243.07
Value Rate is for money saving service agreement customers only.
Service Agreement Customer Benefits
m Member Priority Service		m On-Going Customer Discounts
m Bottom line Cost Benefit		m Preventative Maintenance
Fewer system repairs and safety inspections

WANT TO PAY LESS? – Ask about additional savings than those listed below!

All In One Complete Electric Panel: Install one surface mount all in one combination meter distribution panel with up to 16 poles. All grounding to water pipe and ground rods. Price does not include riser or mast. Price does not include permit or inspection, does not include any repairs to the interior or exterior walls Price includes balancing load and torquing to manufacturers specifications.
Surface Mount E130 300.78 100 amp 220 volt single phase 1-14025-100 amp panel w/main breaker, 1-14030-8’x5/8” ground rod, 20’-10183 #6/1 armored ground, 1-14036-Ground rod clamp 5/8”, 4-11515-Ground Clamps, 1-12127-2P30A Breaker, 1-12130-2P40A Breaker, 1-12133-2P50A Brkr, 10-12109-1P15a or 20a Brkr, 4-11060A-3/8” Fender washers, 4-R3312A-5/16” x 2 lag bolts 10’-10084-#8 Bare Solid Wire E135 360.104 200 amp 220 volt single phase 1-14029-200 amp panel w/main breaker, 1-14030-8’x5/8” ground rod, 20’-10183 #6/1 armored ground, 1-14036-Ground rod clamp 5/8”, 4-11515-Ground Clamps, 1-12127-2P30A Breaker, 1-12130-2P40A Breaker, 1-12133-2P50A Brkr, 10-12109-1P15a or 20a Brkr, 4-11060A-3/8” Fender washers, 4-R3312A-5/16” x 2 lag bolts 10’-10084-#8 Bare Solid Wire Equipment brands: Challenger, GE or other equal value. NOTE: All service upgrade prices are priced for panel to stay in the same location. Relocation of panel will increase price at a rate of $74.00 per foot. PERMIT REQUIRED BY THE CITY. Check for overloaded circuits. Any additional breakers beyond 16 poles refer to page 12 for additional costs. Does Customer need extra branch circuits?			$4,570.80 $5,066.10
Value Rate is for money saving service agreement customers only.
Service Agreement Customer Benefits
m Member Priority Service		m On-Going Customer Discounts
m Bottom line Cost Benefit		m Preventative Maintenance
Fewer system repairs and safety inspections

WANT TO PAY LESS? – Ask about additional savings than those listed below!

Meter & Riser: Install one new meter base overhead mount and run up to 10 feet of mast with weather head and strike wire. This installation also includes any necessary or required grounding up to current NEC standards. Please refer to feeders over 10 feet at the end of this section. Price does not include permit or inspection, does not include any repairs to the interior or exterior walls Price includes balancing load and torquing to manufacturers specifications.
Overhead Mount E140 323.79 100 amp 220 volt single phase (no main breaker) 1-14026A-100 amp panel, 1-R5412 1-‘x1 ½ “ Galv. Conduit, 1-11611 1 ½ “ Ent Hub, 2-1½ “2 Hole Conduit Strp, 1-11629-1½ “ Weatherhd, 1-11638-Roof flashing, 1-‘10096 #4 Thhn wire, 1-14032-8’x5/8” grnd rod ½” 3-12853- Alum to copper splicers or spil bolts, 1-14036-Ground rod clamp, 20’#6/1 armored ground wire, 4-11515 Bronze ground clamp, 16oz-21323 roof mastic, 1-½” Grnd Bshng, 10’ 12109 #8 Bore Grnd 4-14060A-3/8” Washers (flat), 4-R3312A-5/16” x 2 lag bolts E145 375.108 200 amp 220 volt single phase (no main breaker) 1-10429A-200 amp panel, 1-R5413 10-‘x 2 “ Galv. Conduit, 1-11614 2 “ Ent Hub, 2-2 “2 Hole Conduit Strp, 1-11630-2 “ Weatherhd, 1-11641-Roof flashing, 1-‘10045-33’ 20Thhnwire, 1-14032-8’x3/4” grndrod ½” 3-12853- Alum to copper splicers or spil bolts, 1-14036-Ground rod clamp, 20’#4/1 armored ground wire, 4-11515 Bronze ground clamp, 16oz-21323 roof mastic, 1-½” Grnd Bshng, 10’ 12109 #8 Bore Grnd 4-14060A-3/8” Washers (flat), 4-R3312A-5/16” x 2 lag bolts Equipment brands: Challenger, GE or other equal value. NOTE: Relocation of panel will increase price. PERMIT REQUIRED BY THE CITY. Check for overloaded circuits. Any additional breakers beyond 16 poles refer to page 12 for additional costs. Does Customer need extra branch circuits? It is wise to have the electrician check for any existing circuits that are overloaded so they can be split up or added.			$3,536.00 $4,121.00
Value Rate is for money saving service agreement customers only.
Service Agreement Customer Benefits
m Member Priority Service		m On-Going Customer Discounts
m Bottom line Cost Benefit		m Preventative Maintenance
Fewer system repairs and safety inspections

WANT TO PAY LESS? – Ask about additional savings than those listed below!

Meter & Underground Stub: We will install one new meter base, including an underground stub with a 90 degree sweep to facilitate the power company wires and requirements. If grounding is necessary or required, it will be provided at no extra charge and performed up to current NEC standards. Price does not include permit or inspection, does not include any repairs to the interior or exterior walls Price includes balancing load and torquing to manufacturers specifications.
Meter And Underground Stub E147 300.50 100 amp 220 volt 1-14028A-Meter Mount panel (No Main Breaker) 10-R5412 1 ½“ Galv. Conduit, 1-11611 1 ½ entrance hub, 1-11638 1 ½ roof flashing, 1-21323 Mastic, 4-R3308 Roof Nails, R2705 Galv. Straps for surface mounts E148 300.76 200 amp 220 volt 1-10429A-200 amp panel (No Main Breaker) 1-R5413 Galv. Conduit, 1-11614 Ent Hub, 1-11641-2 “ Roof flashing, 10-21323 Roof mastic, 4-3308 Roof Nails, R2706 Galv. Straps for surface mounts. NOTE: PERMIT REQUIRED BY THE CITY. Any additional breakers beyond 16 poles refer to page 12 for additional costs. Does Customer need extra branch circuits? On underground stubs, the service wire is almost always not provided by us because most times the power company pulls straight into the meter. Doing this helps to avoid splices underground.			$2,749.50 $3,100.50
Value Rate is for money saving service agreement customers only.
Service Agreement Customer Benefits
m Member Priority Service		m On-Going Customer Discounts
m Bottom line Cost Benefit		m Preventative Maintenance
Fewer system repairs and safety inspections

WANT TO PAY LESS? – Ask about additional savings than those listed below!

Panel Only (Water Tight): Install one new panel up to 16 poles of breakers. Ground to plumbing and ground rods. All copper used. This installation also includes any necessary or required grounding up to current NEC standards. Please refer to feeders over 10 feet at the end of this section. Price does not include permit or inspection, does not include any repairs to the interior or exterior walls.